Proteus 3000 Power Bank
110850
10
Description: 3000mAh power bank with a handy carry strap which has three premium branding options. It offers the choice of a full colour resin coated finish, an aluminium finish which laser engraves to an oxidised white colour and a PU leather look finish which is debossed. The input power is 5V/800mA and the output power is 5V/1A. It can be recharged in 4–5 hours from a USB port or a mains adapter.
Comprehensive instructions and a Micro-B USB cable are included. An optional EVA carry case and a triple connector cable are available on request.
Colour: Black.
Dimensions:
- Power bank: L 118mm × W 60mm × 9mm.
- Carry case: L 139mm × W 80mm × 50mm.
Packaging: Individual box or an optional carry case.
Price: from NZD$14.28 unbranded. See your price—use the price calculator below.
Printing template (PDF file):
-
Laser Engraving Powerbank: 90mm × 50mm.×
Laser Engraving
Laser engraving produces a permanent natural finish using a laser to mark the product. Different materials produce different effects when engraved so to avoid uncertainty pre-production samples are recommended.
Advantages
- Higher perceived value than other forms of branding.
- The branding becomes part of the surface and is permanent.
- Gives a similar finish to etching on glassware at a much lower cost.
- Can mark curved or uneven products.
- Can produce variable data including individual names.
- The product can be shipped as soon as marking is finished.
Limitations
- The size of branding areas is limited on curved surfaces.
- Fine detail can be lost on smaller products like pens.
Artwork Requirements
- Artwork should be supplied in vector format.
-
Full Colour Print (Resin Coated Finish) Powerbank: 115mm × 57mm (plus bleed if required).×
Resin Coated Finish
Resin coated finish is produced by printing the artwork onto a vinyl material with strong adhesive on the reverse. The branded area is coated with a crystal clear resin which is allowed to dry. Once dry, the finished decal is applied to the product and the adhesive forms a permanent bond.
Advantages
- Ideal for producing vivid full colour images as well as spot colour branding.
- Produces a stunning 3D effect that elevates the perceived value of a product.
- Can print variable data including individual names.
- Only one set up charge is required irrespective of the number of print colours.
- Branding can bleed off the resin coated area.
Limitations
- Only approximate PMS colours can be reproduced.
- The resin requires a one day curing period before the product can be shipped.
- Metallic gold and silver colours are not available.
- Larger print areas tend to be more expensive.
Artwork Requirements
- Artwork can be supplied in either vector or bitmap format.
- Bleed of 3mm should be added to the artwork if it bleeds off the product (the image goes to the edge).
-
Debossing Powerbank: 90mm × 50mm.×
Debossing
Debossing is produced by pressing a hot engraved metal plate into the surface of a product with a lot of pressure. This produces a permanent image below the products surface.
Advantages
- Higher perceived value than other forms of branding.
- The branding becomes part of the product and is permanent.
- The product can be shipped as soon as heat pressing is finished.
Limitations
- Has a higher initial setup cost than other forms of branding as an engraved metal plate must be made. This is a one off cost and is not applicable to repeat orders if the artwork remains unchanged.
Artwork Requirements
- Artwork should be supplied in vector format.
-
-
Specific Colour Print Carry case: 65mm × 30mm.×
Pad Print
Pad printing uses a silicone pad to transfer an image to a product from a laser etched printing plate. It is one of the most popular and affordable ways of branding promotional products due to its ability to reproduce images on uneven or curved products and print multiple colours in a single pass.
Advantages
- Ideal for printing on curved or uneven products.
- Close PMS matches are possible on white or light coloured products.
- Metallic gold and silver is available.
Limitations
- Halftones cannot be consistently reproduced.
- The size of branding areas is limited on curved surfaces.
- Unable to print variable data.
- Close PMS matches are more difficult on darker products and will only be approximate.
- Minor print distortion may occur on uneven or curved surfaces.
- Pad print inks require a curing period before the product can be shipped.
- A set up charge is required for each colour to be printed.
Artwork Requirements
- Artwork should be supplied in vector format.
(Colours)- 1
- 2
- 3
- 4
-
Stock Levels
(Quantity = currently in stock; Next Shipment = when even more stock arrives with supplier)
| Item | Quantity | Next Shipment |
|---|---|---|
| Black Power Bank | 250+ | - |
| Aluminium Plate-Laser Engravin | 250+ | - |
| PU Plate- Debossing | 250+ | - |
Leadtime: Allow around 2 weeks from artwork approval/payment receipt to delivery to your attended courier address (depending on stock availability and branding methods).
